README.md

MIDI Synthesizer Proof of Concept 1

Feedback is very welcome!

• Author: Douglas P. Fields, Jr.
• My portions Copyright 2024 Douglas P. Fields, Jr.
• My portions License: Creative Commons Attribution-ShareAlike 4.0
  • AKA CC BY-SA 4.0
  • See LICENSE.md or CC site
• Started 2024-09-28
• Last updated 2024-10-25
• Repo Self-Link

Overviews:

• Front 3D View
• Schematic PDF
• Board Plots as PDF
• Interactive BOM

Design documents:

• Design notes
• Designed in KiCAD 8
• LCSC part numbers included for assembly by JLCPCB

Software:

• Pinout
• STM Synth
• My KiCAD Libraries

Discussions:

• Smaller Optoisolator

Production Runs

Run 1

• Submitted: 2024-10-27
• Git Commit: 6f9e281abe9c22ef3b995376c3df42217fc04524
• Producer: JLCPCB
  • Order #W202410271206812
• Boards: 5
• Assemblies: 2
• BOM
• CPL
• Gerbers
• JLCPCB Corrected Part Placement
• JLCPCB Submission
• Status: Production complete; in DHL's hands for delivery Nov 8
• Cost:
  • PCB: $28.02
  • Assembly: $79.66
  • Shipping: $32.60
  • Sales tax: $11.22
  • Total: $151.50

Miscellaneous Notes

• Footprints, models, etc., by their respective authors
• Some footprints, schematics, models are from these sources:
  • Component Search Engine
  • Snap EDA
  • EasyEDA
• Useful tools:
  • EasyEDA2KiCAD
  • JLC Parts Finder

KiCAD Configuration Notes

Using EasyEDA2KiCAD:

• Create a Path Substitution
  • Use main KiCAD window: Prefernces -> Configure Paths...
  • EASYEDA2KICAD
  • Git Repository
• Create a Footprint Library
  • easyeda2kicad Nickname
  • ${EASYEDA2KICAD}/easyeda2kicad.pretty
• Create a Symbol Library
  • easyeda2kicad Nickname
  • ${EASYEDA2KICAD}/easyeda2kicad.kicad_sym Library Path

Status

• Schematic: Done
• LCSC part IDs: Almost Done
  • Need non-Red LEDs
• Schematic symbols: Done
• Footprints: Done
• 3D models: Done
• PCB Layout: Done
• Production 1 run: Done - in shipping

TODOs

• Find a much smaller Opto-isolator for MIDI than the one chosen here
  • TLP2362 is used by Ksoloti 0.6. Tested to work with 1.8kΩ pull-up resistor instead of the schematic's 2.7kΩ. (Also worked with no pull-up resistor!)
• Use a 4-pin 32kHz clock?
• RN1 footprint and 3D model look a little bit off - footprint is a bit too small?
• Test points/pins
• MCU Pin 24 is not used - it is I2S1_MCK

Board Layout Notes

4-layer design with Signal/GND/GND/Signal for EVT board.

Will do most important routing first on the top copper layer:

• Decoupling/bypass capacitors
• Clock signals
• High speed signals
  • USB
  • DAC
  • SWD

Remaining signals will be routed using "Manhattan routing." That is, one signal layer will run up/down, the other will run left/right, mostly.

• Top layer: up/down
• Bottom layer: left/right

After that, do these routings:

• Audio signals
• MIDI signals
• SPI
• I²C
• UI (Buttons, LEDs)
• GPIO
• Power

Fill in some positive power areas with fill.

Finally, the signal layers will be filled with GND at the end, and the ground planes should be stitched together with lots of vias.

After Layout Is Done

• DRC check
• Cleanup Tracks & Vias

BOM Notes

• Docs say you need a 4.7 uF ceramic capacitor with low ESR DS11853 Rev 9 page 105
  • Samsung CL10A475KO8NNNC works but Datasheet doesn't say what the ESR is, just "low ESR"
  • Notes on the Cap

Notes for future

• Use fewer header types, they're all extended parts
• Don't use the Resistor Network - due to the Extended parts fee from JLC
  • OTOH there are no 56Ω resistors in the Basic parts library
  • C25127 is an extended part 0402
  • C17714 is an 0805 47Ω
• Add I/O activity LEDs for MIDI & serial?