forked from Fechinator/FechdaKernel
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathKconfig.debug
1316 lines (1112 loc) · 44.9 KB
/
Kconfig.debug
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
config PRINTK_TIME
bool "Show timing information on printks"
depends on PRINTK
help
Selecting this option causes timing information to be
included in printk output. This allows you to measure
the interval between kernel operations, including bootup
operations. This is useful for identifying long delays
in kernel startup. Or add printk.time=1 at boot-time.
See Documentation/kernel-parameters.txt
config DEFAULT_MESSAGE_LOGLEVEL
int "Default message log level (1-7)"
range 1 7
default "4"
help
Default log level for printk statements with no specified priority.
This was hard-coded to KERN_WARNING since at least 2.6.10 but folks
that are auditing their logs closely may want to set it to a lower
priority.
config ENABLE_WARN_DEPRECATED
bool "Enable __deprecated logic"
default y
help
Enable the __deprecated logic in the kernel build.
Disable this to suppress the "warning: 'foo' is deprecated
(declared at kernel/power/somefile.c:1234)" messages.
config ENABLE_MUST_CHECK
bool "Enable __must_check logic"
default y
help
Enable the __must_check logic in the kernel build. Disable this to
suppress the "warning: ignoring return value of 'foo', declared with
attribute warn_unused_result" messages.
config FRAME_WARN
int "Warn for stack frames larger than (needs gcc 4.4)"
range 0 8192
default 1024 if !64BIT
default 2048 if 64BIT
help
Tell gcc to warn at build time for stack frames larger than this.
Setting this too low will cause a lot of warnings.
Setting it to 0 disables the warning.
Requires gcc 4.4
config MAGIC_SYSRQ
bool "Magic SysRq key"
depends on !UML
help
If you say Y here, you will have some control over the system even
if the system crashes for example during kernel debugging (e.g., you
will be able to flush the buffer cache to disk, reboot the system
immediately or dump some status information). This is accomplished
by pressing various keys while holding SysRq (Alt+PrintScreen). It
also works on a serial console (on PC hardware at least), if you
send a BREAK and then within 5 seconds a command keypress. The
keys are documented in <file:Documentation/sysrq.txt>. Don't say Y
unless you really know what this hack does.
config STRIP_ASM_SYMS
bool "Strip assembler-generated symbols during link"
default n
help
Strip internal assembler-generated symbols during a link (symbols
that look like '.Lxxx') so they don't pollute the output of
get_wchan() and suchlike.
config UNUSED_SYMBOLS
bool "Enable unused/obsolete exported symbols"
default y if X86
help
Unused but exported symbols make the kernel needlessly bigger. For
that reason most of these unused exports will soon be removed. This
option is provided temporarily to provide a transition period in case
some external kernel module needs one of these symbols anyway. If you
encounter such a case in your module, consider if you are actually
using the right API. (rationale: since nobody in the kernel is using
this in a module, there is a pretty good chance it's actually the
wrong interface to use). If you really need the symbol, please send a
mail to the linux kernel mailing list mentioning the symbol and why
you really need it, and what the merge plan to the mainline kernel for
your module is.
config DEBUG_FS
bool "Debug Filesystem"
help
debugfs is a virtual file system that kernel developers use to put
debugging files into. Enable this option to be able to read and
write to these files.
For detailed documentation on the debugfs API, see
Documentation/DocBook/filesystems.
If unsure, say N.
config HEADERS_CHECK
bool "Run 'make headers_check' when building vmlinux"
depends on !UML
help
This option will extract the user-visible kernel headers whenever
building the kernel, and will run basic sanity checks on them to
ensure that exported files do not attempt to include files which
were not exported, etc.
If you're making modifications to header files which are
relevant for userspace, say 'Y', and check the headers
exported to $(INSTALL_HDR_PATH) (usually 'usr/include' in
your build tree), to make sure they're suitable.
config DEBUG_SECTION_MISMATCH
bool "Enable full Section mismatch analysis"
help
The section mismatch analysis checks if there are illegal
references from one section to another section.
During linktime or runtime, some sections are dropped;
any use of code/data previously in these sections would
most likely result in an oops.
In the code, functions and variables are annotated with
__init, __devinit, etc. (see the full list in include/linux/init.h),
which results in the code/data being placed in specific sections.
The section mismatch analysis is always performed after a full
kernel build, and enabling this option causes the following
additional steps to occur:
- Add the option -fno-inline-functions-called-once to gcc commands.
When inlining a function annotated with __init in a non-init
function, we would lose the section information and thus
the analysis would not catch the illegal reference.
This option tells gcc to inline less (but it does result in
a larger kernel).
- Run the section mismatch analysis for each module/built-in.o file.
When we run the section mismatch analysis on vmlinux.o, we
lose valueble information about where the mismatch was
introduced.
Running the analysis for each module/built-in.o file
tells where the mismatch happens much closer to the
source. The drawback is that the same mismatch is
reported at least twice.
- Enable verbose reporting from modpost in order to help resolve
the section mismatches that are reported.
config DEBUG_KERNEL
bool "Kernel debugging"
help
Say Y here if you are developing drivers or trying to debug and
identify kernel problems.
config DEBUG_SHIRQ
bool "Debug shared IRQ handlers"
depends on DEBUG_KERNEL && GENERIC_HARDIRQS
help
Enable this to generate a spurious interrupt as soon as a shared
interrupt handler is registered, and just before one is deregistered.
Drivers ought to be able to handle interrupts coming in at those
points; some don't and need to be caught.
config LOCKUP_DETECTOR
bool "Detect Hard and Soft Lockups"
depends on DEBUG_KERNEL && !S390
help
Say Y here to enable the kernel to act as a watchdog to detect
hard and soft lockups.
Softlockups are bugs that cause the kernel to loop in kernel
mode for more than 20 seconds, without giving other tasks a
chance to run. The current stack trace is displayed upon
detection and the system will stay locked up.
Hardlockups are bugs that cause the CPU to loop in kernel mode
for more than 10 seconds, without letting other interrupts have a
chance to run. The current stack trace is displayed upon detection
and the system will stay locked up.
The overhead should be minimal. A periodic hrtimer runs to
generate interrupts and kick the watchdog task every 4 seconds.
An NMI is generated every 10 seconds or so to check for hardlockups.
The frequency of hrtimer and NMI events and the soft and hard lockup
thresholds can be controlled through the sysctl watchdog_thresh.
config HARDLOCKUP_DETECTOR
def_bool LOCKUP_DETECTOR && PERF_EVENTS && HAVE_PERF_EVENTS_NMI && \
!HAVE_NMI_WATCHDOG
config BOOTPARAM_HARDLOCKUP_PANIC
bool "Panic (Reboot) On Hard Lockups"
depends on LOCKUP_DETECTOR
help
Say Y here to enable the kernel to panic on "hard lockups",
which are bugs that cause the kernel to loop in kernel
mode with interrupts disabled for more than 10 seconds (configurable
using the watchdog_thresh sysctl).
Say N if unsure.
config BOOTPARAM_HARDLOCKUP_PANIC_VALUE
int
depends on LOCKUP_DETECTOR
range 0 1
default 0 if !BOOTPARAM_HARDLOCKUP_PANIC
default 1 if BOOTPARAM_HARDLOCKUP_PANIC
config BOOTPARAM_SOFTLOCKUP_PANIC
bool "Panic (Reboot) On Soft Lockups"
depends on LOCKUP_DETECTOR
help
Say Y here to enable the kernel to panic on "soft lockups",
which are bugs that cause the kernel to loop in kernel
mode for more than 20 seconds (configurable using the watchdog_thresh
sysctl), without giving other tasks a chance to run.
The panic can be used in combination with panic_timeout,
to cause the system to reboot automatically after a
lockup has been detected. This feature is useful for
high-availability systems that have uptime guarantees and
where a lockup must be resolved ASAP.
Say N if unsure.
config BOOTPARAM_SOFTLOCKUP_PANIC_VALUE
int
depends on LOCKUP_DETECTOR
range 0 1
default 0 if !BOOTPARAM_SOFTLOCKUP_PANIC
default 1 if BOOTPARAM_SOFTLOCKUP_PANIC
config DETECT_HUNG_TASK
bool "Detect Hung Tasks"
depends on DEBUG_KERNEL
default LOCKUP_DETECTOR
help
Say Y here to enable the kernel to detect "hung tasks",
which are bugs that cause the task to be stuck in
uninterruptible "D" state indefinitiley.
When a hung task is detected, the kernel will print the
current stack trace (which you should report), but the
task will stay in uninterruptible state. If lockdep is
enabled then all held locks will also be reported. This
feature has negligible overhead.
config DEFAULT_HUNG_TASK_TIMEOUT
int "Default timeout for hung task detection (in seconds)"
depends on DETECT_HUNG_TASK
default 120
help
This option controls the default timeout (in seconds) used
to determine when a task has become non-responsive and should
be considered hung.
It can be adjusted at runtime via the kernel.hung_task_timeout_secs
sysctl or by writing a value to
/proc/sys/kernel/hung_task_timeout_secs.
A timeout of 0 disables the check. The default is two minutes.
Keeping the default should be fine in most cases.
config BOOTPARAM_HUNG_TASK_PANIC
bool "Panic (Reboot) On Hung Tasks"
depends on DETECT_HUNG_TASK
help
Say Y here to enable the kernel to panic on "hung tasks",
which are bugs that cause the kernel to leave a task stuck
in uninterruptible "D" state.
The panic can be used in combination with panic_timeout,
to cause the system to reboot automatically after a
hung task has been detected. This feature is useful for
high-availability systems that have uptime guarantees and
where a hung tasks must be resolved ASAP.
Say N if unsure.
config BOOTPARAM_HUNG_TASK_PANIC_VALUE
int
depends on DETECT_HUNG_TASK
range 0 1
default 0 if !BOOTPARAM_HUNG_TASK_PANIC
default 1 if BOOTPARAM_HUNG_TASK_PANIC
config SCHED_DEBUG
bool "Collect scheduler debugging info"
depends on DEBUG_KERNEL && PROC_FS
default y
help
If you say Y here, the /proc/sched_debug file will be provided
that can help debug the scheduler. The runtime overhead of this
option is minimal.
config SYSRQ_SCHED_DEBUG
bool "Print scheduling debugging info from sysrq-trigger"
depends on SCHED_DEBUG
default y
help
If you say Y here, the "show-task-states(T)" and
"show-blocked-tasks(W)" sysrq-triggers will print additional
scheduling statistics.
config SCHEDSTATS
bool "Collect scheduler statistics"
depends on DEBUG_KERNEL && PROC_FS
help
If you say Y here, additional code will be inserted into the
scheduler and related routines to collect statistics about
scheduler behavior and provide them in /proc/schedstat. These
stats may be useful for both tuning and debugging the scheduler
If you aren't debugging the scheduler or trying to tune a specific
application, you can say N to avoid the very slight overhead
this adds.
config TIMER_STATS
bool "Collect kernel timers statistics"
depends on DEBUG_KERNEL && PROC_FS
help
If you say Y here, additional code will be inserted into the
timer routines to collect statistics about kernel timers being
reprogrammed. The statistics can be read from /proc/timer_stats.
The statistics collection is started by writing 1 to /proc/timer_stats,
writing 0 stops it. This feature is useful to collect information
about timer usage patterns in kernel and userspace. This feature
is lightweight if enabled in the kernel config but not activated
(it defaults to deactivated on bootup and will only be activated
if some application like powertop activates it explicitly).
config DEBUG_OBJECTS
bool "Debug object operations"
depends on DEBUG_KERNEL
help
If you say Y here, additional code will be inserted into the
kernel to track the life time of various objects and validate
the operations on those objects.
config DEBUG_OBJECTS_SELFTEST
bool "Debug objects selftest"
depends on DEBUG_OBJECTS
help
This enables the selftest of the object debug code.
config DEBUG_OBJECTS_FREE
bool "Debug objects in freed memory"
depends on DEBUG_OBJECTS
help
This enables checks whether a k/v free operation frees an area
which contains an object which has not been deactivated
properly. This can make kmalloc/kfree-intensive workloads
much slower.
config DEBUG_OBJECTS_TIMERS
bool "Debug timer objects"
depends on DEBUG_OBJECTS
help
If you say Y here, additional code will be inserted into the
timer routines to track the life time of timer objects and
validate the timer operations.
config DEBUG_OBJECTS_WORK
bool "Debug work objects"
depends on DEBUG_OBJECTS
help
If you say Y here, additional code will be inserted into the
work queue routines to track the life time of work objects and
validate the work operations.
config DEBUG_OBJECTS_RCU_HEAD
bool "Debug RCU callbacks objects"
depends on DEBUG_OBJECTS
help
Enable this to turn on debugging of RCU list heads (call_rcu() usage).
config DEBUG_OBJECTS_PERCPU_COUNTER
bool "Debug percpu counter objects"
depends on DEBUG_OBJECTS
help
If you say Y here, additional code will be inserted into the
percpu counter routines to track the life time of percpu counter
objects and validate the percpu counter operations.
config DEBUG_OBJECTS_ENABLE_DEFAULT
int "debug_objects bootup default value (0-1)"
range 0 1
default "1"
depends on DEBUG_OBJECTS
help
Debug objects boot parameter default value
config DEBUG_SLAB
bool "Debug slab memory allocations"
depends on DEBUG_KERNEL && SLAB && !KMEMCHECK
help
Say Y here to have the kernel do limited verification on memory
allocation as well as poisoning memory on free to catch use of freed
memory. This can make kmalloc/kfree-intensive workloads much slower.
config DEBUG_SLAB_LEAK
bool "Memory leak debugging"
depends on DEBUG_SLAB
config SLUB_DEBUG_ON
bool "SLUB debugging on by default"
depends on SLUB && SLUB_DEBUG && !KMEMCHECK
default n
help
Boot with debugging on by default. SLUB boots by default with
the runtime debug capabilities switched off. Enabling this is
equivalent to specifying the "slub_debug" parameter on boot.
There is no support for more fine grained debug control like
possible with slub_debug=xxx. SLUB debugging may be switched
off in a kernel built with CONFIG_SLUB_DEBUG_ON by specifying
"slub_debug=-".
config SLUB_STATS
default n
bool "Enable SLUB performance statistics"
depends on SLUB && SYSFS
help
SLUB statistics are useful to debug SLUBs allocation behavior in
order find ways to optimize the allocator. This should never be
enabled for production use since keeping statistics slows down
the allocator by a few percentage points. The slabinfo command
supports the determination of the most active slabs to figure
out which slabs are relevant to a particular load.
Try running: slabinfo -DA
config DEBUG_KMEMLEAK
bool "Kernel memory leak detector"
depends on DEBUG_KERNEL && EXPERIMENTAL && \
(X86 || ARM || PPC || MIPS || S390 || SPARC64 || SUPERH || MICROBLAZE || TILE)
select DEBUG_FS
select STACKTRACE if STACKTRACE_SUPPORT
select KALLSYMS
select CRC32
help
Say Y here if you want to enable the memory leak
detector. The memory allocation/freeing is traced in a way
similar to the Boehm's conservative garbage collector, the
difference being that the orphan objects are not freed but
only shown in /sys/kernel/debug/kmemleak. Enabling this
feature will introduce an overhead to memory
allocations. See Documentation/kmemleak.txt for more
details.
Enabling DEBUG_SLAB or SLUB_DEBUG may increase the chances
of finding leaks due to the slab objects poisoning.
In order to access the kmemleak file, debugfs needs to be
mounted (usually at /sys/kernel/debug).
config DEBUG_KMEMLEAK_EARLY_LOG_SIZE
int "Maximum kmemleak early log entries"
depends on DEBUG_KMEMLEAK
range 200 40000
default 400
help
Kmemleak must track all the memory allocations to avoid
reporting false positives. Since memory may be allocated or
freed before kmemleak is initialised, an early log buffer is
used to store these actions. If kmemleak reports "early log
buffer exceeded", please increase this value.
config DEBUG_KMEMLEAK_TEST
tristate "Simple test for the kernel memory leak detector"
depends on DEBUG_KMEMLEAK && m
help
This option enables a module that explicitly leaks memory.
If unsure, say N.
config DEBUG_KMEMLEAK_DEFAULT_OFF
bool "Default kmemleak to off"
depends on DEBUG_KMEMLEAK
help
Say Y here to disable kmemleak by default. It can then be enabled
on the command line via kmemleak=on.
config DEBUG_PREEMPT
bool "Debug preemptible kernel"
depends on DEBUG_KERNEL && PREEMPT && TRACE_IRQFLAGS_SUPPORT
default y
help
If you say Y here then the kernel will use a debug variant of the
commonly used smp_processor_id() function and will print warnings
if kernel code uses it in a preemption-unsafe way. Also, the kernel
will detect preemption count underflows.
config DEBUG_RT_MUTEXES
bool "RT Mutex debugging, deadlock detection"
depends on DEBUG_KERNEL && RT_MUTEXES
help
This allows rt mutex semantics violations and rt mutex related
deadlocks (lockups) to be detected and reported automatically.
config DEBUG_PI_LIST
bool
default y
depends on DEBUG_RT_MUTEXES
config RT_MUTEX_TESTER
bool "Built-in scriptable tester for rt-mutexes"
depends on DEBUG_KERNEL && RT_MUTEXES
help
This option enables a rt-mutex tester.
config DEBUG_SPINLOCK
bool "Spinlock and rw-lock debugging: basic checks"
depends on DEBUG_KERNEL
select UNINLINE_SPIN_UNLOCK
help
Say Y here and build SMP to catch missing spinlock initialization
and certain other kinds of spinlock errors commonly made. This is
best used in conjunction with the NMI watchdog so that spinlock
deadlocks are also debuggable.
config DEBUG_MUTEXES
bool "Mutex debugging: basic checks"
depends on DEBUG_KERNEL
help
This feature allows mutex semantics violations to be detected and
reported.
config DEBUG_LOCK_ALLOC
bool "Lock debugging: detect incorrect freeing of live locks"
depends on DEBUG_KERNEL && TRACE_IRQFLAGS_SUPPORT && STACKTRACE_SUPPORT && LOCKDEP_SUPPORT
select DEBUG_SPINLOCK
select DEBUG_MUTEXES
select LOCKDEP
help
This feature will check whether any held lock (spinlock, rwlock,
mutex or rwsem) is incorrectly freed by the kernel, via any of the
memory-freeing routines (kfree(), kmem_cache_free(), free_pages(),
vfree(), etc.), whether a live lock is incorrectly reinitialized via
spin_lock_init()/mutex_init()/etc., or whether there is any lock
held during task exit.
config PROVE_LOCKING
bool "Lock debugging: prove locking correctness"
depends on DEBUG_KERNEL && TRACE_IRQFLAGS_SUPPORT && STACKTRACE_SUPPORT && LOCKDEP_SUPPORT
select LOCKDEP
select DEBUG_SPINLOCK
select DEBUG_MUTEXES
select DEBUG_LOCK_ALLOC
select TRACE_IRQFLAGS
default n
help
This feature enables the kernel to prove that all locking
that occurs in the kernel runtime is mathematically
correct: that under no circumstance could an arbitrary (and
not yet triggered) combination of observed locking
sequences (on an arbitrary number of CPUs, running an
arbitrary number of tasks and interrupt contexts) cause a
deadlock.
In short, this feature enables the kernel to report locking
related deadlocks before they actually occur.
The proof does not depend on how hard and complex a
deadlock scenario would be to trigger: how many
participant CPUs, tasks and irq-contexts would be needed
for it to trigger. The proof also does not depend on
timing: if a race and a resulting deadlock is possible
theoretically (no matter how unlikely the race scenario
is), it will be proven so and will immediately be
reported by the kernel (once the event is observed that
makes the deadlock theoretically possible).
If a deadlock is impossible (i.e. the locking rules, as
observed by the kernel, are mathematically correct), the
kernel reports nothing.
NOTE: this feature can also be enabled for rwlocks, mutexes
and rwsems - in which case all dependencies between these
different locking variants are observed and mapped too, and
the proof of observed correctness is also maintained for an
arbitrary combination of these separate locking variants.
For more details, see Documentation/lockdep-design.txt.
config PROVE_RCU
bool "RCU debugging: prove RCU correctness"
depends on PROVE_LOCKING
default n
help
This feature enables lockdep extensions that check for correct
use of RCU APIs. This is currently under development. Say Y
if you want to debug RCU usage or help work on the PROVE_RCU
feature.
Say N if you are unsure.
config PROVE_RCU_REPEATEDLY
bool "RCU debugging: don't disable PROVE_RCU on first splat"
depends on PROVE_RCU
default n
help
By itself, PROVE_RCU will disable checking upon issuing the
first warning (or "splat"). This feature prevents such
disabling, allowing multiple RCU-lockdep warnings to be printed
on a single reboot.
Say Y to allow multiple RCU-lockdep warnings per boot.
Say N if you are unsure.
config SPARSE_RCU_POINTER
bool "RCU debugging: sparse-based checks for pointer usage"
default n
help
This feature enables the __rcu sparse annotation for
RCU-protected pointers. This annotation will cause sparse
to flag any non-RCU used of annotated pointers. This can be
helpful when debugging RCU usage. Please note that this feature
is not intended to enforce code cleanliness; it is instead merely
a debugging aid.
Say Y to make sparse flag questionable use of RCU-protected pointers
Say N if you are unsure.
config LOCKDEP
bool
depends on DEBUG_KERNEL && TRACE_IRQFLAGS_SUPPORT && STACKTRACE_SUPPORT && LOCKDEP_SUPPORT
select STACKTRACE
select FRAME_POINTER if !MIPS && !PPC && !ARM_UNWIND && !S390 && !MICROBLAZE
select KALLSYMS
select KALLSYMS_ALL
config LOCK_STAT
bool "Lock usage statistics"
depends on DEBUG_KERNEL && TRACE_IRQFLAGS_SUPPORT && STACKTRACE_SUPPORT && LOCKDEP_SUPPORT
select LOCKDEP
select DEBUG_SPINLOCK
select DEBUG_MUTEXES
select DEBUG_LOCK_ALLOC
default n
help
This feature enables tracking lock contention points
For more details, see Documentation/lockstat.txt
This also enables lock events required by "perf lock",
subcommand of perf.
If you want to use "perf lock", you also need to turn on
CONFIG_EVENT_TRACING.
CONFIG_LOCK_STAT defines "contended" and "acquired" lock events.
(CONFIG_LOCKDEP defines "acquire" and "release" events.)
config DEBUG_LOCKDEP
bool "Lock dependency engine debugging"
depends on DEBUG_KERNEL && LOCKDEP
help
If you say Y here, the lock dependency engine will do
additional runtime checks to debug itself, at the price
of more runtime overhead.
config TRACE_IRQFLAGS
bool
help
Enables hooks to interrupt enabling and disabling for
either tracing or lock debugging.
config DEBUG_ATOMIC_SLEEP
bool "Sleep inside atomic section checking"
select PREEMPT_COUNT
depends on DEBUG_KERNEL
help
If you say Y here, various routines which may sleep will become very
noisy if they are called inside atomic sections: when a spinlock is
held, inside an rcu read side critical section, inside preempt disabled
sections, inside an interrupt, etc...
config DEBUG_LOCKING_API_SELFTESTS
bool "Locking API boot-time self-tests"
depends on DEBUG_KERNEL
help
Say Y here if you want the kernel to run a short self-test during
bootup. The self-test checks whether common types of locking bugs
are detected by debugging mechanisms or not. (if you disable
lock debugging then those bugs wont be detected of course.)
The following locking APIs are covered: spinlocks, rwlocks,
mutexes and rwsems.
config STACKTRACE
bool "Stacktrace"
depends on STACKTRACE_SUPPORT
default y
config DEBUG_STACK_USAGE
bool "Stack utilization instrumentation"
depends on DEBUG_KERNEL
help
Enables the display of the minimum amount of free stack which each
task has ever had available in the sysrq-T and sysrq-P debug output.
This option will slow down process creation somewhat.
config DEBUG_KOBJECT
bool "kobject debugging"
depends on DEBUG_KERNEL
help
If you say Y here, some extra kobject debugging messages will be sent
to the syslog.
config DEBUG_HIGHMEM
bool "Highmem debugging"
depends on DEBUG_KERNEL && HIGHMEM
help
This options enables addition error checking for high memory systems.
Disable for production systems.
config DEBUG_BUGVERBOSE
bool "Verbose BUG() reporting (adds 70K)" if DEBUG_KERNEL && EXPERT
depends on BUG
depends on ARM || AVR32 || M32R || M68K || SPARC32 || SPARC64 || \
FRV || SUPERH || GENERIC_BUG || BLACKFIN || MN10300 || TILE
default y
help
Say Y here to make BUG() panics output the file name and line number
of the BUG call as well as the EIP and oops trace. This aids
debugging but costs about 70-100K of memory.
config DEBUG_INFO
bool "Compile the kernel with debug info"
depends on DEBUG_KERNEL
help
If you say Y here the resulting kernel image will include
debugging info resulting in a larger kernel image.
This adds debug symbols to the kernel and modules (gcc -g), and
is needed if you intend to use kernel crashdump or binary object
tools like crash, kgdb, LKCD, gdb, etc on the kernel.
Say Y here only if you plan to debug the kernel.
If unsure, say N.
config DEBUG_INFO_REDUCED
bool "Reduce debugging information"
depends on DEBUG_INFO
help
If you say Y here gcc is instructed to generate less debugging
information for structure types. This means that tools that
need full debugging information (like kgdb or systemtap) won't
be happy. But if you merely need debugging information to
resolve line numbers there is no loss. Advantage is that
build directory object sizes shrink dramatically over a full
DEBUG_INFO build and compile times are reduced too.
Only works with newer gcc versions.
config DEBUG_VM
bool "Debug VM"
depends on DEBUG_KERNEL
help
Enable this to turn on extended checks in the virtual-memory system
that may impact performance.
If unsure, say N.
config DEBUG_VIRTUAL
bool "Debug VM translations"
depends on DEBUG_KERNEL && X86
help
Enable some costly sanity checks in virtual to page code. This can
catch mistakes with virt_to_page() and friends.
If unsure, say N.
config DEBUG_NOMMU_REGIONS
bool "Debug the global anon/private NOMMU mapping region tree"
depends on DEBUG_KERNEL && !MMU
help
This option causes the global tree of anonymous and private mapping
regions to be regularly checked for invalid topology.
config DEBUG_WRITECOUNT
bool "Debug filesystem writers count"
depends on DEBUG_KERNEL
help
Enable this to catch wrong use of the writers count in struct
vfsmount. This will increase the size of each file struct by
32 bits.
If unsure, say N.
config DEBUG_MEMORY_INIT
bool "Debug memory initialisation" if EXPERT
default !EXPERT
help
Enable this for additional checks during memory initialisation.
The sanity checks verify aspects of the VM such as the memory model
and other information provided by the architecture. Verbose
information will be printed at KERN_DEBUG loglevel depending
on the mminit_loglevel= command-line option.
If unsure, say Y
config DEBUG_LIST
bool "Debug linked list manipulation"
depends on DEBUG_KERNEL
help
Enable this to turn on extended checks in the linked-list
walking routines.
If unsure, say N.
config TEST_LIST_SORT
bool "Linked list sorting test"
depends on DEBUG_KERNEL
help
Enable this to turn on 'list_sort()' function test. This test is
executed only once during system boot, so affects only boot time.
If unsure, say N.
config DEBUG_SG
bool "Debug SG table operations"
depends on DEBUG_KERNEL
help
Enable this to turn on checks on scatter-gather tables. This can
help find problems with drivers that do not properly initialize
their sg tables.
If unsure, say N.
config DEBUG_NOTIFIERS
bool "Debug notifier call chains"
depends on DEBUG_KERNEL
help
Enable this to turn on sanity checking for notifier call chains.
This is most useful for kernel developers to make sure that
modules properly unregister themselves from notifier chains.
This is a relatively cheap check but if you care about maximum
performance, say N.
config DEBUG_CREDENTIALS
bool "Debug credential management"
depends on DEBUG_KERNEL
help
Enable this to turn on some debug checking for credential
management. The additional code keeps track of the number of
pointers from task_structs to any given cred struct, and checks to
see that this number never exceeds the usage count of the cred
struct.
Furthermore, if SELinux is enabled, this also checks that the
security pointer in the cred struct is never seen to be invalid.
If unsure, say N.
#
# Select this config option from the architecture Kconfig, if it
# is preferred to always offer frame pointers as a config
# option on the architecture (regardless of KERNEL_DEBUG):
#
config ARCH_WANT_FRAME_POINTERS
bool
help
config FRAME_POINTER
bool "Compile the kernel with frame pointers"
depends on DEBUG_KERNEL && \
(CRIS || M68K || FRV || UML || \
AVR32 || SUPERH || BLACKFIN || MN10300) || \
ARCH_WANT_FRAME_POINTERS
default y if (DEBUG_INFO && UML) || ARCH_WANT_FRAME_POINTERS
help
If you say Y here the resulting kernel image will be slightly
larger and slower, but it gives very useful debugging information
in case of kernel bugs. (precise oopses/stacktraces/warnings)
config BOOT_PRINTK_DELAY
bool "Delay each boot printk message by N milliseconds"
depends on DEBUG_KERNEL && PRINTK && GENERIC_CALIBRATE_DELAY
help
This build option allows you to read kernel boot messages
by inserting a short delay after each one. The delay is
specified in milliseconds on the kernel command line,
using "boot_delay=N".
It is likely that you would also need to use "lpj=M" to preset
the "loops per jiffie" value.
See a previous boot log for the "lpj" value to use for your
system, and then set "lpj=M" before setting "boot_delay=N".
NOTE: Using this option may adversely affect SMP systems.
I.e., processors other than the first one may not boot up.
BOOT_PRINTK_DELAY also may cause LOCKUP_DETECTOR to detect
what it believes to be lockup conditions.
config RCU_TORTURE_TEST
tristate "torture tests for RCU"
depends on DEBUG_KERNEL
default n
help
This option provides a kernel module that runs torture tests
on the RCU infrastructure. The kernel module may be built
after the fact on the running kernel to be tested, if desired.
Say Y here if you want RCU torture tests to be built into
the kernel.
Say M if you want the RCU torture tests to build as a module.
Say N if you are unsure.
config RCU_TORTURE_TEST_RUNNABLE
bool "torture tests for RCU runnable by default"
depends on RCU_TORTURE_TEST = y
default n
help
This option provides a way to build the RCU torture tests
directly into the kernel without them starting up at boot
time. You can use /proc/sys/kernel/rcutorture_runnable
to manually override this setting. This /proc file is
available only when the RCU torture tests have been built
into the kernel.
Say Y here if you want the RCU torture tests to start during
boot (you probably don't).
Say N here if you want the RCU torture tests to start only
after being manually enabled via /proc.
config RCU_CPU_STALL_TIMEOUT
int "RCU CPU stall timeout in seconds"
depends on TREE_RCU || TREE_PREEMPT_RCU
range 3 300
default 60
help
If a given RCU grace period extends more than the specified
number of seconds, a CPU stall warning is printed. If the
RCU grace period persists, additional CPU stall warnings are
printed at more widely spaced intervals.
config RCU_CPU_STALL_VERBOSE
bool "Print additional per-task information for RCU_CPU_STALL_DETECTOR"
depends on TREE_PREEMPT_RCU
default y
help
This option causes RCU to printk detailed per-task information
for any tasks that are stalling the current RCU grace period.
Say N if you are unsure.
Say Y if you want to enable such checks.
config RCU_CPU_STALL_INFO
bool "Print additional diagnostics on RCU CPU stall"
depends on (TREE_RCU || TREE_PREEMPT_RCU) && DEBUG_KERNEL
default n
help
For each stalled CPU that is aware of the current RCU grace
period, print out additional per-CPU diagnostic information
regarding scheduling-clock ticks, idle state, and,
for RCU_FAST_NO_HZ kernels, idle-entry state.
Say N if you are unsure.
Say Y if you want to enable such diagnostics.
config RCU_TRACE
bool "Enable tracing for RCU"
depends on DEBUG_KERNEL
help
This option provides tracing in RCU which presents stats
in debugfs for debugging RCU implementation.
Say Y here if you want to enable RCU tracing
Say N if you are unsure.
config KPROBES_SANITY_TEST
bool "Kprobes sanity tests"
depends on DEBUG_KERNEL
depends on KPROBES
default n
help
This option provides for testing basic kprobes functionality on
boot. A sample kprobe, jprobe and kretprobe are inserted and
verified for functionality.
Say N if you are unsure.
config BACKTRACE_SELF_TEST
tristate "Self test for the backtrace code"
depends on DEBUG_KERNEL
default n
help
This option provides a kernel module that can be used to test
the kernel stack backtrace code. This option is not useful
for distributions or general kernels, but only for kernel
developers working on architecture code.
Note that if you want to also test saved backtraces, you will
have to enable STACKTRACE as well.
Say N if you are unsure.
config DEBUG_BLOCK_EXT_DEVT
bool "Force extended block device numbers and spread them"
depends on DEBUG_KERNEL
depends on BLOCK
default n