SMA Sunny Boy 3.7 | battery 1 power: read failed: dial tcp #14462
Replies: 4 comments 4 replies
-
It seems that reconnecting the networks helps, but not as final solution |
Beta Was this translation helpful? Give feedback.
-
I still have the same issue and cannot reproduce the issue. After a while, sometimes a day, sometimes a week, I get the battery error message. |
Beta Was this translation helpful? Give feedback.
-
Bricht da nur die Verbindung zwischen dem Sunny Boy und EVCC ab? Ich hatte das Problem, dass der Sunny Boy, ähnlich wie bei dir, nach einem nicht reproduzierbaren Zeitraum die Kommunikation eingestellt hat. Ich habe dann alle SMA-Komponenten und den EVCC-Rasperry-Pi hinter einen eigenen, kaskadierten Router gesteckt, so dass diese in ihrem eigenen Subnetz sind. Seitdem (über 1 Jahr) hatte ich keinen einzigen Verbindugnsabbruch mehr. |
Beta Was this translation helpful? Give feedback.
-
Ich hatte keinen konkreten Verdacht und hab dann einfach einen Router davor gepackt. |
Beta Was this translation helpful? Give feedback.
-
Seit zwei Tagen habe das Problem, dass evcc den SMA SunnyBoy nicht mehr auslesen kann und im Log die Meldung "battery 1 power: read failed: dial tcp" erscheint.
[site ] INFO 2024/06/18 16:35:33 site config:
[site ] INFO 2024/06/18 16:35:33 meters: grid ✓ pv ✓ battery ✓
[site ] INFO 2024/06/18 16:35:33 grid: power ✓ energy ✓ currents ✓
[site ] INFO 2024/06/18 16:35:33 pv 1: power ✓ energy ✓ currents ✓
[site ] INFO 2024/06/18 16:35:33 battery 1: power ✓ energy ✓ currents ✗ soc ✓ capacity ✗
[site ] INFO 2024/06/18 16:35:33 vehicles:
[site ] INFO 2024/06/18 16:35:33 vehicle 1: range ✓ finish ✓ status ✓ climate ✗ wakeup ✓
[lp-1 ] INFO 2024/06/18 16:35:33 loadpoint 1:
[lp-1 ] INFO 2024/06/18 16:35:33 mode: pv
[lp-1 ] INFO 2024/06/18 16:35:33 charger: power ✗ energy ✗ currents ✗ phases ✗ wakeup ✗
[lp-1 ] INFO 2024/06/18 16:35:33 meters: charge ✗
[site ] DEBUG 2024/06/18 16:35:33 set buffer soc: 100
[site ] DEBUG 2024/06/18 16:35:33 set priority soc: 90
[lp-1 ] DEBUG 2024/06/18 16:35:33 !! active phases: 3p = min(0p measured 0p vehicle 3p physical 0p charger)
[lp-1 ] DEBUG 2024/06/18 16:35:33 phase timer inactive
[lp-1 ] DEBUG 2024/06/18 16:35:33 pv timer inactive
[lp-1 ] DEBUG 2024/06/18 16:35:33 max charge current: 6A
[lp-1 ] DEBUG 2024/06/18 16:35:33 !! active phases: 3p = min(0p measured 0p vehicle 3p physical 0p charger)
[site ] DEBUG 2024/06/18 16:35:33 ----
[lp-1 ] DEBUG 2024/06/18 16:35:33 charge power: 0W
[site ] DEBUG 2024/06/18 16:35:33 pv power: 5364W
[site ] ERROR 2024/06/18 16:35:43 battery 1 power: read failed: dial tcp 192.19.0.153:502: i/o timeout
die Config ist folgende:
type: template
template: sma-sbs-modbus
usage: battery
modbus: tcpip
id: 3
host: 192.19.0.153 # Hostname
port: 502 # Port
Gab es ein Update oder liegt es an einer neuen Evcc Version?
Beta Was this translation helpful? Give feedback.
All reactions