-
Notifications
You must be signed in to change notification settings - Fork 92
Task List
Benjamin Vernoux edited this page May 31, 2021
·
281 revisions
The first place to look for open tasks that you can help with is the Issues List.
The following list will be removed once everything is moved to the Issues List, completed, or obsolete. If you are interested in helping with any of these tasks, coordinate with the person in parentheses. Try IRC first (libera.chat channel #hydrabus at libera.chat), then email.
- nlfx has Implemented serprog protocol SPI speed for flashrom (PR#124) (before it was hard coded to max speed)
- UART Baud rate detector
- Memory pool allocator for temporary buffers
- Replace the CAN ID filter to a mask filter
- TBD
-
Add new utilities:
- Multimeter up to 3.3V/7.2MSPS(12bits) with logging in µSD file in real-time.
-
Bootloader idea using official HydraBus (bootloader) OpenMoko USB ID:
- USB DFU boot like implemented in actual firmware by keeping UBTN pressed during power ON.
- Read a configuration file from SDcard(if present) and boot a custom firmware from SDcard(execution in SRAM).
- other idea TBD.
-
Protection/Debug features(for developer):
- Implement basic stack overflow/underflow check with canaries between each stack (probably need chibios patch)
- Implement advanced stack overflow/underflow protection using M4F MPU
- Generate DAC output advanced mode using waveform and DMA to generate Sin, Square ...
- Add Offset and Frequency parameter for waveforms.
- 1-Wire:
- Add overdrive mode
- i2c:
- Slave mode
- Number of bits (7, 8, 10)
- spi:
- Number of bits (any number)
- Waveform generator
- Measure time between two pin states using hardware timer
- New modes:
- Parallel Bus (2 to 32bits) with mode sniffer, read and write (with option to log data in realtime to MicroSD) (depending on feedback)
- 1 or 3 Wire with mode sniffer
- Basic Scope up to 3.3V and up to 7.2MSPS/12bits
-
Nand Flash x16 support(WILL NOT BE SUPPORTED, see Nand support #12)
- USB 1.x/2.0 LS/FS sniffer mode (using special passthrough mode with logging directly to MicroSD) (see USB sniffer capability #21)
HydraNFC Shield v1.0 is now superseded by HydraNFC Shield v2 in an other fork see https://github.com/hydrabus/hydrafw_hydranfc_shield_v2 for more details
- Extension using EEPROM:
- Implement support of EEPROM extension detection with same hw & content as Beagle bone defined here
DONE (please test with HydraFW v0.10):
- NAND flash mode. To test with more flash memories
- Wiegand mode
- LIN mode with HydraLINCAN shield
- CAN1 and CAN2 with HydraLINCAN Shield
- 1-Wire scan command with multiple devices
- AVR flash / dump (do more tests)
- Binary mode (to do more tests)
- JTAG (with different MCU/CPU and report what work what do not work ...)
- CHANGELOG
- Console commands
- Binary mode guide
-
NFC/HydraNFC v1 guide
- Read UID of an ISO/IEC_14443 Tag
- Read UID and data of a MIFARE Ultralight Tag
- Read UID of an ISO/IEC 15693 Tag
- Emul ISO14443a Tag
- Emul MIFARE Ultralight Tag
- Emul Mifare Classic Tag
- Unique NFC sniffer design
- Launch NFC sniffer from console
- Sniffer ISO14443A wireshark pcap
- Autonomous/stand-alone sniffer mode
- Sniffer ISO14443A real-time infinite trace mode
- HydraFW-HydraNFC-v1.x-TRF7970A-Tutorial