1.9.0 Release notes

Please read the release notes carefully and upgrade INAV Configurator application.

INAV is and will remain open-source and free, but you are more than welcome to support the development.

This release was supported by our awesome sponsors CarbonBird.com, Airbot, ADPM Drones and a number of supporters on Patreon.

WARNINGS

If you are using HMC5883/HMC5983 compass it is advised to recalibrate. Please don't restore the old settings from the dump/diff script.

Known bugs

todo

Renamed `PASSTHROUGH` flight mode

The PASSTHROUGH flight mode has been renamed to MANUAL. New settings also have been added to allow the use of different servo rates or control weight for the servos when flying without stabilization without using a programmable remote control. The exposition settings for roll/pitch and yaw controls are now also also independent from the exposition settings used for stabilized flight modes. See the manual_* settings in the CLI settings table below. The default settings make the MANUAL flight mode behave exactly as the old PASSTHROUGH flight mode.

Increased VBAT resolution

The battery voltage resolution has been increased from 100mV to 10mV. In consequence the vbat_scale, vbat_max_cell_voltage, vbat_warning_cell_voltage and vbat_min_cell_voltage settings resolution has also been increased 10 fold allowing more precise battery voltage calibration and battery voltage thresholds. To restore old configuration settings users need to multiply their old setting values by 10.

New defaults for these settings:

vbat_scale: 1100 (was 110)
vbat_max_cell_voltage: 424 (was 43) or 4.24V/cell
vbat_warning_cell_voltage: 350 (was 35) or 3.5V/cell
vbat_min_cell_voltage: 330 (was 33) or 3.3V/cell

Users who were using the old defaults should not use the settings from their dump but use the new defaults instead.

Users now have the option to display 1 or 2 decimals for battery voltages in the OSD display (see osd_main_voltage_decimals in the CLI settings table below).

Battery capacity monitoring

It is now possible to display the remaining battery capacity in the OSD and also use the battery capacity thresholds (battery_capacity_warning and battery_capacity_critical) for battery alarms.

For the capacity monitoring to work you need a current sensor (CURRENT_METER feature). For monitoring energy in milliWatt hour you also need voltage measurement (VBAT feature). For best results the current and voltage readings have to be calibrated.

For the remaining battery capacity to be displayed users need to set the battery_capacity setting (>0) and the battery to be full when plugged in. If the battery_capacity setting is set to 0 the remaining battery capacity item in the OSD will display NA and the battery gauge will use an estimation based on the battery voltage (like it used to be) otherwise it will display the remaining battery capacity down to the battery_capacity_critical setting (battery considered empty) and the battery gauge will be based on the remaining capacity. For the capacity thresholds to be used for alarms the battery_capacity_warning and battery_capacity_critical settings also needs to be set (>0) and the plugged in battery to be full when plugged in.

For the battery to be considered full the mean cell voltage of the battery needs to be above vbat_max_cell_voltage - 140mV (by default 4.1V). So a 3S battery will be considered full above 12.3V and a 4S battery above 16.24V. If the battery plugged in is not considered full the remaining battery capacity OSD item will show NF (Not Full).

For the remaining battery capacity and battery gauge to be the most precise (linear relative to throttle from full to empty) when using battery capacity monitoring users should use the milliWatt hour unit for the battery capacity settings. The battery capacity settings unit can be set using the battery_capacity_unit setting (see the CLI parameters table below).

CLI parameter renaming / new parameters

New parameters have been introduced. Some CLI parameters were renamed to support new features or to better reflect their meaning:

Name	Description
`rangefinder_median_filter`	Default is OFF
`baro_median_filter`	Default is ON
`failsafe_lights`	Enable or disable the lights when the `FAILSAFE` flight mode is enabled. The target needs to be compiled with `USE_LIGHTS` [ON/OFF]. Default is ON
`failsafe_lights_flash_period`	Time in milliseconds between two flashes when `failsafe_lights` is ON and `FAILSAFE` flight mode is enabled [40-65535]. Default is 1000ms.
`failsafe_lights_flash_on_time`	Flash lights ON time in milliseconds when `failsafe_lights` is ON and `FAILSAFE` flight mode is enabled. [20-65535]. Default is 100ms.
`battery_capacity`	Set the battery capacity in mAh or mWh (see `battery_capacity_unit`). Used to calculate the remaining battery capacity. Default is 0
`battery_capacity_warning`	If the remaining battery capacity goes below this threshold the beeper will emit short beeps and the relevant OSD items will blink. Default is 0
`battery_capacity_critical`	If the remaining battery capacity goes below this threshold the battery is considered empty and the beeper will emit long beeps. Default is 0
`battery_capacity_unit`	Unit used for `battery_capacity`, `battery_capacity_warning` and `battery_capacity_critical` [MAH/MWH] (milliAmpere hour / milliWatt hour). Default is MAH
`manual_rc_expo`	Exposition value used for the PITCH/ROLL axes by the `MANUAL` flight mode [0-100]. Default is 70
`manual_rc_yaw_expo`	Exposition value used for the YAW axis by the `MANUAL` flight mode. Default is 20
`manual_pitch_rate`	Servo travel multiplier for the PITCH axis in `MANUAL` flight mode [0-100]%. Default is 100%
`manual_roll_rate`	Servo travel multiplier for the ROLL axis in `MANUAL` flight mode [0-100]%. Default is 100%
`manual_yaw_rate`	Servo travel multiplier for the YAW axis in `MANUAL` flight mode [0-100]%. Default is 100%
`gps_ublox_use_galileo`	Enable use of Galileo satellites. This is at the expense of other regional constellations, so benefit may also be regional. Requires M8N and Ublox firmware 3.x (or later) [OFF/ON]. Default is OFF
`smartport_fuel_unit`	Unit of the value sent with the `FUEL` ID through the S.Port telemetry. Replaces the `smartport_fuel_percent` setting [PERCENT/MAH/MWH]. Default is PERCENT
`osd_stats_energy_unit`	Unit used for the drawn energy in the OSD stats [MAH/WH] (milliAmpere hour/ Watt hour). Default is MAH
`osd_main_voltage_decimals`	Number of decimals for the battery voltages displayed in the OSD [1-2]. Default is 1
`osd_wh_drawn_pos`
`osd_bat_remaining_capacity_pos`
`osd_bat_remaining_percent_pos`
`osd_efficiency_mah_pos`
`osd_efficiency_wh_pos`
`display_force_sw_blink`
`mag_to_use`	Allow to chose between built-in and external compass sensor if they are connected to separate buses. Currently only for REVO target
`nav_fw_launch_min_time`	Allow launch mode to execute at least this time (ms) and ignore stick movements [0-60000]. Default is 0
`nav_fw_launch_max_altitude`	Altitude (centimeters) at which LAUNCH mode will be turned off and regular flight mode will take over [0-60000]. Default is 0

New boards

Betaflight F3
Betaflight F4
FuriousFPV F35 Lightning (former FuriousFPV WingF4)
Matek F722
Matek F405-CTR
Holybro KAKUTE F4
Holybro KAKUTE F4 V2
Fortini F4

New features

[COMPASS] Allow to chose between internal and external compass on REVO target (@digitalentity, #2522)
[COMPASS] Support for QMC5883 compass chips that incorrectly mimic the HMC58883 (@digitalentity, #2809)
[SYSTEM] Migrate to busDevice abstraction layer for better device access abstraction (@digitalentity, #2290)
[SYSTEM] Create dedicated F427 startup file (@digitalentity, #2559)
[MOTOLAB] Allow MOTOLAB target to be used for airplanes (@shellixyz, #2502)
[GPS] Enables use of Galileo satellites for NEO-M8N GPS units (@stronnag, #2583)
[CALIBRATION] Add API for Calibration tab in Configurator
[OSD] Allow OSD mode to disable OSD (@shellixyz, #2676)
[OSD] Increase odometer accuracy (@digitalentity, #2757)
[OSD] Add more battery-related indicators (including efficiency)
[LIGHTS] Add LIGHTS flight mode to enable/disable GPIO-driven equipment (@shellixyz, #2675)
[LAUNCH] Allow LAUNCH mode to ignore sticks for certain amount of time (@shellixyz, #2677)
[LAUNCH] Allow LAUNCH mode to be permanently enabled as FW_LAUNCH feature (@giacomo892, #2731)
[MSP] API to support smix/mmix configuration via Configurator (@DzikuVx, #2693)
[MSP] Add no-reply flag to allow MSP messages that don't need a response (@digitalentity, #2762)
[COMPASS] Enable QMC5883, MAG3110 and IST8310 on most of the targets (@digitalentity, #2699)
[AIRPLANE] Replace PASSTHROUGH with MANUAL flight mode (@shellixyz, #2661)
[BATTERY] Improve battery monitoring and resolution (@shellixyz, #2705)
[SYSTEM] Remove SoftSPI implementation since it's not used (@DzikuVx, #2726)
[SYSTEM] Allow in-flight adjustments of board alignment, cruise throttle and pitch2thr (@shellixyz, #2768)
[SYSTEM] Trace messages output for easier debugging (@digitalentity, #2691)

Bugfixes

Fix flash overflow on F7 targets due to usage of flash_split (@digitalentity, #2535)
Update BLHeli passthrough to support BLHeli_32
Fix AK8963 compass support (@digitalentity, #2551)
Fix timer clash between motors and servos on PIKOBLX (@shellixyz, #2513)
Fix non-working UART7/8
Fix non-booting OMNIBUSF4 (some variants with MPU6500-family gyro) (@shellixyz, #2575)
Fix support for dataflash chips larger than 16MiB (@digitalentity, #2633)
Fix VCP issues on F7 targets (@digitalentity, #2647)
Fix potential buffer overflow in MSPv2 parsing (@digitalentity, #2689)
Fix OSD statistics displaying issues on NTSC screens (@krzysztofmatula, #2721)
Fix RCSplit not being detected (increase timeout) (@digitalentity, #2767)
Fix OSD blinking on some flawed OSD hardware (allow software blinking) (@fiam, #2452)
Fix P gains for Heading Hold not available in CLI (@DzikuVx, #2669)
Fix arming with AUTOTRIM enabled (@giacomo892, #2756)
Fix hardfault in ledstrip driver due to division by zero (@digitalentity, #2790)