-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathBTFL_cli_backup_PAVO_PICO_20241012_063611_BETAFPVF405.txt
154 lines (128 loc) · 2.82 KB
/
BTFL_cli_backup_PAVO_PICO_20241012_063611_BETAFPVF405.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
defaults nosave
# version
# Betaflight / STM32F405 (S405) 4.4.1 Apr 13 2023 / 06:44:52 (e43d591b2) MSP API: 1.45
# config: YES
# start the command batch
batch start
# reset configuration to default settings
defaults nosave
board_name BETAFPVF405
manufacturer_id BEFH
mcu_id 001a00233133471633353636
signature
# name: Pavo Pico
# feature
feature -AIRMODE
feature TELEMETRY
# serial
serial 3 131073 115200 57600 0 115200
# beeper
beeper -GYRO_CALIBRATED
beeper -RX_LOST
beeper -RX_LOST_LANDING
beeper -DISARMING
beeper -ARMING
beeper -ARMING_GPS_FIX
beeper -BAT_CRIT_LOW
beeper -BAT_LOW
beeper -GPS_STATUS
beeper -RX_SET
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -DISARM_REPEAT
beeper -ARMED
beeper -SYSTEM_INIT
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH_FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSE
beeper -RC_SMOOTHING_INIT_FAIL
# beacon
beacon RX_LOST
beacon RX_SET
# led
led 0 0,0::CO:10
led 1 1,0::CO:10
# aux
aux 0 0 0 1925 2100 0 0
aux 1 1 1 1300 2100 0 0
aux 2 1 4 1925 2100 0 0
aux 3 2 2 1925 2100 0 0
aux 4 2 5 1925 2100 0 0
aux 5 13 3 1425 2100 0 0
aux 6 35 3 1650 2100 0 0
# master
set gyro_lpf2_static_hz = 0
set dyn_notch_count = 0
set dyn_notch_q = 500
set gyro_lpf1_dyn_min_hz = 0
set acc_calibration = -7,18,-15,1
set baro_hardware = AUTO
set serialrx_provider = CRSF
set blackbox_sample_rate = 1/2
set blackbox_device = NONE
set dshot_idle_value = 1150
set dshot_bidir = ON
set motor_output_reordering = 2,3,0,1,4,5,6,7
set failsafe_procedure = AUTO-LAND
set align_board_roll = 180
set vbat_min_cell_voltage = 335
set vbat_warning_cell_voltage = 345
set ibata_scale = 510
set ibata_offset = -300
set small_angle = 180
set pid_process_denom = 2
set osd_vbat_pos = 2561
set osd_rssi_pos = 192
set osd_link_quality_pos = 2496
set osd_rssi_dbm_pos = 2464
set osd_rsnr_pos = 160
set osd_tim_2_pos = 3629
set osd_flymode_pos = 3598
set osd_throttle_pos = 3566
set osd_crosshairs_pos = 2361
set osd_current_pos = 2592
set osd_craft_name_pos = 2582
set osd_warnings_pos = 14837
set osd_esc_tmp_pos = 129
set osd_core_temp_pos = 225
set vtx_band = 0
set vtx_channel = 0
set vtx_power = 0
set vtx_freq = 0
set vcd_video_system = HD
set craft_name = Pavo Pico
profile 0
# profile 0
set p_pitch = 56
set i_pitch = 70
set d_pitch = 54
set p_roll = 53
set i_roll = 67
set d_roll = 45
set p_yaw = 53
set i_yaw = 67
set d_min_roll = 43
set d_min_pitch = 51
set feedforward_averaging = 2_POINT
set feedforward_jitter_factor = 10
set simplified_i_gain = 70
set simplified_d_gain = 145
set simplified_pi_gain = 120
set simplified_dmax_gain = 15
set simplified_pitch_d_gain = 105
set tpa_rate = 66
profile 1
profile 2
profile 3
# restore original profile selection
profile 0
rateprofile 0
rateprofile 1
rateprofile 2
rateprofile 3
# restore original rateprofile selection
rateprofile 0
# save configuration