Ideamaker Profiles for Stock Marlin and Original Prusa Firmware

Firmware

• SKR Bear Firmware
• Prusa Firmware

How To

• Profile Import Video

Stock Marlin Setup:

• Step 1: Load Printer Profile (ie. SKR Bear Printer)
• Step 2: Set your esteps in Printer Type > Advanced - Step-E per MM
  • Stock - 280 | BMG - 830 | Pulleybox/LDO Geared - 980
• Step 3: Confirm that Printer type > Advanced - Omit RaiseTouch Specific Gcode is enabled
• Step 4: Confirm that Printer type > Advanced - Relative Extrusion is enabled
• Step 5: Load Profiles (ie. SKR CFPETG)

Stock Prusa Setup:

• Step 1: Load Printer Profile (ie. SKR Bear Printer)
• Step 2: Set your esteps in Printer Type > Advanced - Step-E per MM
  • Stock - 280 | BMG - 830 | Pulleybox/LDO Geared - 980
• Step 3: Confirm that Printer type > Advanced - Change GCode E Length by multiplying filamentg flowrate is enabled
• Step 4: Confirm that Printer type > Advanced - Omit RaiseTouch Specific Gcode is enabled
• Step 5: Confirm that Printer type > Advanced - Relative Extrusion is enabled
• Step 6: Load Profiles (ie. SKR CFPETG)

Start Gcode

Stock Marlin ABL

G90 ; Absolute Positioning
M83 ; extruder relative mode
M140 S{temperature_heatbed} ; set bed temp
M104 S150 ; set extruder temp
M190 S{temperature_heatbed} ; wait for bed temp
G28 ; Home all axes
G29 ; Level Bed
G1 X0 Z0.6 Y-3.0 F3000.0 ;
M104 S{temperature_extruder1} ; set extruder
M109 S{temperature_extruder1} ; wait for extruder temp
M900 K0.05; Linear advance setting
G92 E0.0
G1 Z0.2 X100.0 E30.0 F1000.0 ; intro line
G92 E0.0

Stock Marlin UBL

G90 ; Absolute
M83 ; extruder relative mode
G28 ; Home all axes
G29 L1 ; Load UBL Slot 1
M140 S{temperature_heatbed} ; set bed temp
M190 S{temperature_heatbed} ; wait for bed temp
G29 J2; 4 point mesh tilt
G1 X0 Z0.6 Y-3.0 F3000.0
M104 S{temperature_extruder1} ; set extruder temp
M109 S{temperature_extruder1} ; wait for extruder temp
M900 K0.05; Linear advance setting
G92 E0.0
G1 Z0.2 X100.0 E30.0 F1000.0 ; intro line
G92 E0.0

Stock Prusa Firmware

G90 ; Absolute Positioning
M83 ; extruder relative mode
M140 S{temperature_heatbed} ; set bed temp
M104 S150 ; set extruder temp
M190 S{temperature_heatbed} ; wait for bed temp
G28 W ; home all without mesh bed level
G80 ; mesh bed leveling set 3x3, 5x5, or 7x7 in settings menu
G1 Y-3.0 Z0.6 F1000.0 ; go outside print area for purge
M104 S{temperature_extruder1} ; set extruder
M109 S{temperature_extruder1} ; wait for extruder temp
M900 K30; Linear advance setting LA1.5 value K0.05
G92 E0.0
G1 Z0.2 X100.0 E30.0 F1000.0 ; intro line
G92 E0.0
M221 S95 ; Filament Flowrate

Layer Change Gcode

G92 E0.0