morrownr testing

8852bu.conf

@@ -0,0 +1,195 @@
+# /etc/modprobe.d/8852bu.conf
+#
+# Purpose: Allow easy access to specific driver options.
+#
+# Edit the following line to change, add or delete options:
+options 8852bu rtw_switch_usb_mode=0 rtw_he_enable=1 rtw_vht_enable=1 rtw_dfs_region_domain=0
+#
+# Note: To activate USB3 mode, change `rtw_switch_usb_mode=0` above to
+# `rtw_switch_usb_mode=1`
+#
+# Note: The `options` line shown above is a good default for managed mode. Below is
+# an example for AP mode. Modify as required after reading the documentation:
+#options 8852bu rtw_switch_usb_mode=0 rtw_he_enable=2 rtw_vht_enable=2 rtw_dfs_region_domain=1
+#
+# Note: See documentation for rtw_dfs_region_domain below.
+#
+# After editing is complete, save this file (if using nano: Ctrl + x, y, Enter)
+# and reboot to activate the changes.
+#
+# Documentation:
+#
+# -----
+#
+# USB options: ( rtw_switch_usb_mode )
+#
+# 0 = No switch (default)
+# 1 = Switch from usb 2.0 to usb 3.0
+# 2 = Switch from usb 3.0 to usb 2.0
+#
+# -----
+#
+# HE options ( rtw_he_enable )
+#
+#  0 = Disable
+#  1 = Enable (default)
+#  2 = Force auto enable (use only for AP mode)
+#
+# Notes:
+# - A non-default setting can degrade performance greatly in managed mode.
+# - Option 2 allows 80 MHz channel width for 5GHz AP mode, such as when
+#   you are using hostapd.
+#
+# -----
+#
+# VHT options ( rtw_vht_enable )
+#
+#  0 = Disable
+#  1 = Enable (default)
+#  2 = Force auto enable (use only for AP mode)
+#
+# Notes:
+# - A non-default setting can degrade performance greatly in managed mode.
+# - Option 2 allows 80 MHz channel width for 5GHz AP mode, such as when
+#   you are using hostapd.
+#
+# -----
+#
+# DFS Options ( rtw_dfs_region_domain )
+#
+# 0 = NONE (default)
+# 1 = FCC
+# 2 = MKK
+# 3 = ETSI
+#
+# Notes:
+# - Activates DFS channels in AP mode.
+# - DFS FCC 80 MHz channels for hostapd: 52(58), 100(106), 116(122) and 132(138)
+# - For more information: https://en.wikipedia.org/wiki/List_of_WLAN_channels
+#
+# Note: An AP needs to listen on a DFS channel for a period of 60 seconds
+# before transmitting on the channel. If any radar pulses are detected,
+# the AP cannot use that channel and will have to try a different channel.
+#
+# -----
+#
+# Wireless Mode options ( rtw_wireless_mode )
+#
+# Note: The following settings are for an AC class adapter and need to
+# be updated for AX.
+#
+# 1  = 2.4GHz 802.11b
+# 2  = 2.4GHz 802.11g
+# 3  = 2.4GHz 802.11b/g
+# 4  = 5GHz 802.11a
+# 8  = 2.4Hz 802.11n
+# 11 = 2.4GHz 802.11b/g/n
+# 16 = 5GHz 802.11n
+# 20 = 5GHz 802.11a/n
+# 64 = 5GHz 802.11ac
+# 84 = 5GHz 802.11a/n/ac
+# 95 = 2.4GHz 802.11b/g/n 5GHz 802.11a/n/ac
+#
+# -----
+#
+# To see all options that are available:
+#
+# $ ls /sys/module/8852bu/parameters/
+#
+# if2name                           rtw_max_bss_cnt
+# ifname                            rtw_max_roaming_times
+# rtw_adaptivity_en                 rtw_mp_mode
+# rtw_adaptivity_idle_probability   rtw_network_mode
+# rtw_adaptivity_mode               rtw_OffEfuseMask
+# rtw_adaptivity_th_edcca_hl_diff   rtw_pci_dynamic_aspm_linkctrl
+# rtw_adaptivity_th_l2h_ini         rtw_phl_log_level
+# rtw_ampdu_enable                  rtw_phydm_ability
+# rtw_amplifier_type_2g             rtw_phy_file_path
+# rtw_amplifier_type_5g             rtw_pll_ref_clk_sel
+# rtw_amsdu_mode                    rtw_powertracking_type
+# rtw_antdiv_cfg                    rtw_pwrtrim_enable
+# rtw_antdiv_type                   rtw_qos_opt_enable
+# rtw_ant_num                       rtw_quick_addba_req
+# rtw_ap_fwd_b2u_flags              rtw_quota_turbo_en
+# rtw_ap_src_b2u_flags              rtw_rfe_type
+# rtw_band                          rtw_rfintfs
+# rtw_band_type                     rtw_rfk_ability
+# rtw_bcn_hint_valid_ms             rtw_rf_path
+# rtw_beamform_cap                  rtw_roch_extend_dur
+# rtw_btcoex_enable                 rtw_roch_max_away_dur
+# rtw_busy_thresh                   rtw_roch_min_home_dur
+# rtw_bw_mode                       rtw_rrsr_value
+# rtw_channel                       rtw_rx_ampdu_amsdu
+# rtw_channel_plan                  rtw_rx_ampdu_sz_limit_1ss
+# rtw_check_hw_status               rtw_rx_ampdu_sz_limit_2ss
+# rtw_chip_version                  rtw_rx_ampdu_sz_limit_3ss
+# rtw_ch_switch_offload             rtw_rx_ampdu_sz_limit_4ss
+# rtw_country_code                  rtw_rxgain_offset_2g
+# rtw_country_ie_slave_en_ifbmp     rtw_rxgain_offset_5gh
+# rtw_country_ie_slave_en_mode      rtw_rxgain_offset_5gl
+# rtw_country_ie_slave_en_role      rtw_rxgain_offset_5gm
+# rtw_country_ie_slave_flags        rtw_rx_nss
+# rtw_country_ie_slave_scan_int_ms  rtw_scan_interval_thr
+# rtw_decrypt_phy_file              rtw_scan_pch_ex
+# rtw_dfs_region_domain             rtw_single_ant_path
+# rtw_dis_ch_flags                  rtw_stbc_cap
+# rtw_drv_ant_band_switch           rtw_switch_usb_mode
+# rtw_drv_log_level                 rtw_sw_proto_bf_cap_phy0
+# rtw_dynamic_agg_enable            rtw_sw_proto_bf_cap_phy1
+# rtw_dyn_txbf                      rtw_target_tx_pwr_2g_a
+# rtw_edcca_cs_th                   rtw_target_tx_pwr_2g_b
+# rtw_edcca_th_2g                   rtw_target_tx_pwr_2g_c
+# rtw_edcca_th_5g                   rtw_target_tx_pwr_2g_d
+# rtw_en_dyn_rrsr                   rtw_target_tx_pwr_5g_a
+# rtw_en_ecsa                       rtw_target_tx_pwr_5g_b
+# rtw_en_gro                        rtw_target_tx_pwr_5g_c
+# rtw_en_napi                       rtw_target_tx_pwr_5g_d
+# rtw_en_tdls                       rtw_tx_ampdu_amsdu
+# rtw_excl_chs                      rtw_tx_ampdu_num
+# rtw_FileMaskEfuse                 rtw_TxBBSwing_2G
+# rtw_full_ch_in_p2p_handshake      rtw_TxBBSwing_5G
+# rtw_fw_ofld_cap                   rtw_tx_bw_mode
+# rtw_GLNA_type                     rtw_tx_nss
+# rtw_halrf_ability                 rtw_tx_pwr_by_rate
+# rtw_he_enable                     rtw_tx_pwr_lmt_enable
+# rtw_hiq_filter                    rtw_usb_rxagg_mode
+# rtw_ht_enable                     rtw_user_regd_always_apply
+# rtw_hwpwrp_detect                 rtw_vcs_type
+# rtw_hw_rts_en                     rtw_vht_24g_enable
+# rtw_hw_wps_pbc                    rtw_vht_enable
+# rtw_initmac                       rtw_vht_rx_mcs_map
+# rtw_init_regd_always_apply        rtw_vo_edca
+# rtw_iqk_fw_offload                rtw_vrtl_carrier_sense
+# rtw_lbkmode                       rtw_wifi_spec
+# rtw_load_phy_file                 rtw_wireless_mode
+# rtw_low_power                     rtw_wmm_enable
+# rtw_lowrate_two_xmit              rtw_wowlan_sta_mix_mode
+# rtw_max_amsdu_len
+#
+# -----
+#
+# To see the values that are in use:
+#
+# $ grep [[:alnum:]] /sys/module/8852bu/parameters/*
+#
+# -----
+#
+# hostapd setup information for rtl8852bu
+# Note: The best settings can vary but the following may be a good place to start.
+#
+# /etc/modprobe.d/8852bu.conf
+# options 8852bu rtw_switch_usb_mode=0 rtw_he_enable=2 rtw_vht_enable=2 rtw_dfs_region_domain=1
+#
+# Note: The best setting for `rtw_dfs_region_domain=` will depend on your location.
+#
+# /etc/hostapd/hostapd.conf
+#
+# hw ht capab: 19e3
+#ht_capab=[LDPC][HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][MAX-AMSDU-7935][DSSS_CCK-40]
+#
+# hw vht capab: 03c011b1
+#vht_capab=[MAX-MPDU-7991][RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1][SU-BEAMFORMEE][MU-BEAMFORMEE][VHT-TXOP-PS][HTC-VHT][MAX-A-MPDU-LEN-EXP7]
+#
+# hw he capab: 0x0001120a0060
+#
+# -----