Huawei AP6010DN #3
Open
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
blocktrron
reviewed
Jul 11, 2024
CodingMarco
pushed a commit
that referenced
this pull request
Feb 12, 2025
Ruckus R500 datasheet: https://webresources.ruckuswireless.com/datasheets/r500/ds-ruckus-r500.html Specifications: SoC: 720Mhz QCA9558 RAM: 256MB Storage: 64MB of FLASH (SPI NOR - S25FL512S) 1x AR8327 GB switch Ethernet: 1x1000M port #3 on AR8327, 1x1000M (802.3at POE), port openwrt#5 on AR8327 Wireless: QCA988X HW2.0 802.11ac AR9550 2.4GHz 802.11b/g/n 5x GPIO LED 1x GPIO Reset Button 1x DC Jack 12v 1x UART, 3.3v, 115200 1x TPM, SLB9645TT12 2x Beamforming antennas configured via 74LV164 MAC addresses: 1. art 0x807E | Factory bridged | f0:3e:90:XX:XX:80 | 2. art 0x66 | eth0 | f0:3e:90:XX:XX:83 | (port 5, cpu port 6) - PoE port 3. art 0x6c | eth1 | f0:3e:90:XX:XX:84 | (port 3, cpu port 0) - non PoE port Serial console: 115200-8-N-1 on internal H4 header. Pinout: H1 ----------- |1|x|3|4|5| ----------- Pin 1 is near the "H4" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX JTAG: Connector H2, similar to MIPS eJTAG, standard, unpoulated. H9 ---------------------- |2 |4 |6 |8 |10|12|14| ---------------------- |1 |3 |5 |7 |9 |11|13| ---------------------- 3 - TDI 5 - TDO 7 - TMS 9 - TCK 2,4,6,8,10 - GND 14 - Vref 1,11,12,13 - Not connected I²C: connector H2, near power LED, unpopulated: ------ |1|2|3 ------ H2 1 - SCL 2 - SDA 3 - GND Installation: Serial Port/TFTP 1. Setup tftp server on the local network 2. Connect to UART with TTL 3. Interupt U-boot process with Ctrl-C 4. Setup appropriate ipaddr and serverip in setenv: - setenv ipaddr 192.168.1.1 - setenv serverip 192.168.1.2 5. On TFTP Server - copy openwrt-ath79-generic-ruckus_r500-initramfs-kernel.bin to /srv/tftp 6. On R500 boot into initrd image - tftpboot 0x81000000 openwrt-ath79-generic-ruckus_r500-initramfs-kernel.bin - bootm 0x81000000 7. On TFTP server - scp -O openwrt-ath79-generic-ruckus_r500-squashfs-sysupgrade.bin [email protected]:/tmp 8. Ensure the boot command is set before flashing the image: fw_setenv bootcmd 'bootm 0xbf1c0000' 9. On R500 - sysupgrade /tmp/openwrt-ath79-generic-ruckus_r500-squashfs-sysupgrade.bin 10. If not done in 8; set boot command from U-boot shell itself: - setenv bootcmd bootm 0xbf1c0000 - saveenv - reset This patch adapted from https://github.com/victhor393/openwrt-ruckus-r500/tree/ruckus-r500-master Signed-off-by: Damien Mascord <[email protected]> - Heavily refactored the device tree - Extended commit message - Documented onboad connectors - Refactored MAC and calibration data setups to use nvmem-layout - Made both network interfaces LAN ports and bridge them, this makes more sense for an access point and is consistent with the rest of Ruckus APs. - Enable lzma-loader for compressed initramfs - Enabled the optional internal USB port - Added missing LEDs and according pinctrl settings - Added reserved memory region used for bootloader communication - Added the bit-banged I²C bus and onboard TPM - Refactored boot scheme and flash layout to match earlier Ruckus devices and maximize usable space for user data. Quirks: - H7 is the physical presence switch for the SLB9645TT12 TPM. TODO: - Link state reporting on the Ethernet ports doesn't work and both ports report "up" due to limitation of swconfig ar8327 driver. With DSA conversion, this shall be rectified. - Locate 2nd shift register (U7) controlling beamforming antennas, probably on ath10k GPIOs which are currently unsupported in the driver. For this, there is a device tree node describing that - but explicitly disabled. - At the moment of adding support, there is an endianness bug in the TPM driver causing it to not detect the TPM module because of ID mismatch. Signed-off-by: Lech Perczak <[email protected]> Link: openwrt#17550 Signed-off-by: Hauke Mehrtens <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
No description provided.