🏆T5_E_Paper_S3_Pro🏆

0️⃣ Version 🎁

1、Version

ID	Hardware	Software	Remark
H752-01	v1.0-241224	v1.2_250118	latest
H752	v1.0-240810	v1.0-241203	current

2、Where to buy.

LilyGo Store

1️⃣Product 🎁

Product	T5 E-Paper S3 Pro
MCU	ESP32-S3-WROOM-1
Flash / PSRAM	16M / 8M
Lora	SX1262
Touch	GT911 (0x5D)
Driver IC	ED047TC1 (4.7 inches, 960x540 , 16 gray)
Battery Capacity	1500mAh
Battery Chip	BQ25896 (0x6B), BQ27220 (0x55)
RTC	PCF85063 (0x51)

2️⃣ Module 🎁

Datasheets on the chip are available in ./hardware directory.

Name	Dependency library
SX1262	jgromes/[email protected]
BQ25896	lewisxhe/XPowersLib@^0.2.3
Sensor	lewisxhe/[email protected]
LVGL	lvgl/lvgl@^8.3.11

3️⃣ Quick Start 🎁

🟢 PlatformIO is recommended because these examples were developed on it. 🟢

1、PlatformIO

1. Install Visual Studio Code and Python, and clone or download the project;
2. Search for the PlatformIO plugin in the VisualStudioCode extension and install it;
3. After the installation is complete, you need to restart VisualStudioCode
4. After opening this project, PlatformIO will automatically download the required tripartite libraries and dependencies, the first time this process is relatively long, please wait patiently;
5. After all the dependencies are installed, you can open the platformio.ini configuration file, uncomment in example to select a routine, and then press ctrl+s to save the .ini configuration file;
6. Click ☑️ under VScode to compile the project, then plug in USB and select COM under VScode;
7. Finally, click the ➡️ button to download the program to Flash;

2、Arduino IDE

1. Install Arduino IDE

2. Copy all files under this project/lib/ and paste them into the Arduion library path (generally C:\Users\YourName\Documents\Arduino\libraries);

3. Open the Arduion IDE and click File->Open in the upper left corner to open an example in this project/example/xxx/xxx.ino under this item;

4. Then configure Arduion. After the configuration is completed in the following way, you can click the button in the upper left corner of Arduion to compile and download;

Arduino IDE Setting	Value
Board	ESP32S3 Dev Module
Port	Your port
USB CDC On Boot	Enable
CPU Frequency	240MHZ(WiFi)
Core Debug Level	None
USB DFU On Boot	Disable
Erase All Flash Before Sketch Upload	Disable
Events Run On	Core1
Flash Mode	QIO 80MHZ
Flash Size	16MB(128Mb)
Arduino Runs On	Core1
USB Firmware MSC On Boot	Disable
Partition Scheme	16M Flash(3M APP/9.9MB FATFS)
PSRAM	OPI PSRAM
Upload Mode	UART0/Hardware CDC
Upload Speed	921600
USB Mode	CDC and JTAG

3、Folder structure:

├─boards  : Some information about the board for the platformio.ini configuration project;
├─data    : Picture resources used by the program;
├─example : Some examples;
├─firmare : `factory` compiled firmware;
├─hardware: Schematic diagram of the board, chip data;
├─lib     : Libraries used in the project;

4️⃣ Pins 🎁

#define BOARD_SCL         (5)
#define BOARD_SDA         (6)

#define BOARD_SPI_MISO    (8)
#define BOARD_SPI_MOSI    (17)
#define BOARD_SPI_SCLK    (18)

#define BOARD_SD_MISO    (BOARD_SPI_MISO)
#define BOARD_SD_MOSI    (BOARD_SPI_MOSI)
#define BOARD_SD_SCLK    (BOARD_SPI_SCLK)
#define BOARD_SD_CS      (16)

#define BOARD_LORA_MISO   (BOARD_SPI_MISO)
#define BOARD_LORA_MOSI   (BOARD_SPI_MOSI)
#define BOARD_LORA_SCLK   (BOARD_SPI_SCLK)
#define BOARD_LORA_CS     (46)
#define BOARD_LORA_IRQ    (3)
#define BOARD_LORA_RST    (43)
#define BOARD_LORA_BUSY   (44)

#define BOARD_TOUCH_SCL   (BOARD_SCL)
#define BOARD_TOUCH_SDA   (BOARD_SDA)
#define BOARD_TOUCH_INT   (15)
#define BOARD_TOUCH_RST   (41)

#define BOARD_RTC_INT     7
#define BOARD_RT_SCL      (BOARD_SCL)
#define BOARD_RT_SDA      (BOARD_SDA)

#define BOARD_BL_EN       (40)
#define BOARD_BATT_PIN    (4)
#define BOARD_BOOT_BTN    (0)
#define BOARD_KEY_BTN     (48)

5️⃣ Test 🎁

Sleep power consumption.

6️⃣ FAQ 🎁

Document	Link
How to download programs through flash_download_tool ?	dosc

7️⃣ Schematic & 3D 🎁

For more information, see the ./hardware directory.

Schematic : T5_E-Paper-S3-Pro

3D Files : 3D Files