Linux 3.0.24

Documentation/hwmon/jc42

@@ -7,21 +7,29 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * IDT TSE2002B3, TS3000B3
-    Prefix: 'tse2002b3', 'ts3000b3'
+  * Atmel AT30TS00
+    Prefix: 'at30ts00'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.idt.com/products/getdoc.cfm?docid=18715691
-	http://www.idt.com/products/getdoc.cfm?docid=18715692
+	http://www.atmel.com/Images/doc8585.pdf
+  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
+    Prefix: 'tse2002', 'ts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
+	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -48,6 +56,12 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+  * ST Microelectronics STTS2002, STTS3000
+    Prefix: 'stts2002', 'stts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f

Makefile

@@ -1,6 +1,6 @@
 VERSION = 3
 PATCHLEVEL = 0
-SUBLEVEL = 23
+SUBLEVEL = 24
 EXTRAVERSION =
 NAME = Sneaky Weasel
 

arch/alpha/include/asm/futex.h

@@ -108,7 +108,7 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 	"	lda	$31,3b-2b(%0)\n"
 	"	.previous\n"
 	:	"+r"(ret), "=&r"(prev), "=&r"(cmp)
-	:	"r"(uaddr), "r"((long)oldval), "r"(newval)
+	:	"r"(uaddr), "r"((long)(int)oldval), "r"(newval)
 	:	"memory");
 
 	*uval = prev;

arch/arm/Kconfig

@@ -1199,7 +1199,7 @@ config ARM_ERRATA_743622
 	depends on CPU_V7
 	help
 	  This option enables the workaround for the 743622 Cortex-A9
-	  (r2p0..r2p2) erratum. Under very rare conditions, a faulty
+	  (r2p*) erratum. Under very rare conditions, a faulty
 	  optimisation in the Cortex-A9 Store Buffer may lead to data
 	  corruption. This workaround sets a specific bit in the diagnostic
 	  register of the Cortex-A9 which disables the Store Buffer

arch/arm/mach-dove/common.c

@@ -31,6 +31,7 @@
 #include <asm/mach/arch.h>
 #include <linux/irq.h>
 #include <plat/time.h>
+#include <plat/ehci-orion.h>
 #include <plat/common.h>
 #include "common.h"
 
@@ -74,7 +75,7 @@ void __init dove_map_io(void)
 void __init dove_ehci0_init(void)
 {
 	orion_ehci_init(&dove_mbus_dram_info,
-			DOVE_USB0_PHYS_BASE, IRQ_DOVE_USB0);
+			DOVE_USB0_PHYS_BASE, IRQ_DOVE_USB0, EHCI_PHY_NA);
 }
 
 /*****************************************************************************

arch/arm/mach-kirkwood/common.c

@@ -28,6 +28,7 @@
 #include <plat/cache-feroceon-l2.h>
 #include <plat/mvsdio.h>
 #include <plat/orion_nand.h>
+#include <plat/ehci-orion.h>
 #include <plat/common.h>
 #include <plat/time.h>
 #include "common.h"
@@ -74,7 +75,7 @@ void __init kirkwood_ehci_init(void)
 {
 	kirkwood_clk_ctrl |= CGC_USB0;
 	orion_ehci_init(&kirkwood_mbus_dram_info,
-			USB_PHYS_BASE, IRQ_KIRKWOOD_USB);
+			USB_PHYS_BASE, IRQ_KIRKWOOD_USB, EHCI_PHY_NA);
 }
 
 

arch/arm/mach-lpc32xx/include/mach/irqs.h

@@ -61,7 +61,7 @@
  */
 #define IRQ_LPC32XX_JTAG_COMM_TX	LPC32XX_SIC1_IRQ(1)
 #define IRQ_LPC32XX_JTAG_COMM_RX	LPC32XX_SIC1_IRQ(2)
-#define IRQ_LPC32XX_GPI_11		LPC32XX_SIC1_IRQ(4)
+#define IRQ_LPC32XX_GPI_28		LPC32XX_SIC1_IRQ(4)
 #define IRQ_LPC32XX_TS_P		LPC32XX_SIC1_IRQ(6)
 #define IRQ_LPC32XX_TS_IRQ		LPC32XX_SIC1_IRQ(7)
 #define IRQ_LPC32XX_TS_AUX		LPC32XX_SIC1_IRQ(8)

arch/arm/mach-lpc32xx/irq.c

@@ -118,6 +118,10 @@ static const struct lpc32xx_event_info lpc32xx_events[NR_IRQS] = {
 		.event_group = &lpc32xx_event_pin_regs,
 		.mask = LPC32XX_CLKPWR_EXTSRC_GPI_06_BIT,
 	},
+	[IRQ_LPC32XX_GPI_28] = {
+		.event_group = &lpc32xx_event_pin_regs,
+		.mask = LPC32XX_CLKPWR_EXTSRC_GPI_28_BIT,
+	},
 	[IRQ_LPC32XX_GPIO_00] = {
 		.event_group = &lpc32xx_event_int_regs,
 		.mask = LPC32XX_CLKPWR_INTSRC_GPIO_00_BIT,
@@ -305,9 +309,18 @@ static int lpc32xx_irq_wake(struct irq_data *d, unsigned int state)
 
 		if (state)
 			eventreg |= lpc32xx_events[d->irq].mask;
-		else
+		else {
 			eventreg &= ~lpc32xx_events[d->irq].mask;
 
+			/*
+			 * When disabling the wakeup, clear the latched
+			 * event
+			 */
+			__raw_writel(lpc32xx_events[d->irq].mask,
+				lpc32xx_events[d->irq].
+				event_group->rawstat_reg);
+		}
+
 		__raw_writel(eventreg,
 			lpc32xx_events[d->irq].event_group->enab_reg);
 
@@ -380,13 +393,15 @@ void __init lpc32xx_init_irq(void)
 
 	/* Setup SIC1 */
 	__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC1_BASE));
-	__raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE));
-	__raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE));
+	__raw_writel(SIC1_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE));
+	__raw_writel(SIC1_ATR_DEFAULT,
+				LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE));
 
 	/* Setup SIC2 */
 	__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC2_BASE));
-	__raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE));
-	__raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE));
+	__raw_writel(SIC2_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE));
+	__raw_writel(SIC2_ATR_DEFAULT,
+				LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE));
 
 	/* Configure supported IRQ's */
 	for (i = 0; i < NR_IRQS; i++) {

arch/arm/mach-lpc32xx/serial.c

@@ -88,6 +88,7 @@ struct uartinit {
 	char *uart_ck_name;
 	u32 ck_mode_mask;
 	void __iomem *pdiv_clk_reg;
+	resource_size_t mapbase;
 };
 
 static struct uartinit uartinit_data[] __initdata = {
@@ -97,6 +98,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 5),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
+		.mapbase = LPC32XX_UART5_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
@@ -105,6 +107,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 3),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
+		.mapbase = LPC32XX_UART3_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
@@ -113,6 +116,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 4),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
+		.mapbase = LPC32XX_UART4_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
@@ -121,6 +125,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 6),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
+		.mapbase = LPC32XX_UART6_BASE,
 	},
 #endif
 };
@@ -165,11 +170,24 @@ void __init lpc32xx_serial_init(void)
 
 		/* pre-UART clock divider set to 1 */
 		__raw_writel(0x0101, uartinit_data[i].pdiv_clk_reg);
+
+		/*
+		 * Force a flush of the RX FIFOs to work around a
+		 * HW bug
+		 */
+		puart = uartinit_data[i].mapbase;
+		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
+		__raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
+		j = LPC32XX_SUART_FIFO_SIZE;
+		while (j--)
+			tmp = __raw_readl(
+				LPC32XX_UART_DLL_FIFO(puart));
+		__raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
 	}
 
 	/* This needs to be done after all UART clocks are setup */
 	__raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
-	for (i = 0; i < ARRAY_SIZE(uartinit_data) - 1; i++) {
+	for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
 		/* Force a flush of the RX FIFOs to work around a HW bug */
 		puart = serial_std_platform_data[i].mapbase;
 		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));

arch/arm/mach-mv78xx0/common.c

@@ -20,6 +20,7 @@
 #include <mach/mv78xx0.h>
 #include <mach/bridge-regs.h>
 #include <plat/cache-feroceon-l2.h>
+#include <plat/ehci-orion.h>
 #include <plat/orion_nand.h>
 #include <plat/time.h>
 #include <plat/common.h>
@@ -170,7 +171,7 @@ void __init mv78xx0_map_io(void)
 void __init mv78xx0_ehci0_init(void)
 {
 	orion_ehci_init(&mv78xx0_mbus_dram_info,
-			USB0_PHYS_BASE, IRQ_MV78XX0_USB_0);
+			USB0_PHYS_BASE, IRQ_MV78XX0_USB_0, EHCI_PHY_NA);
 }