docs: add Radxa ROCK 5B docs to Single Board Computer section

website/content/v1.10/talos-guides/configuration/disk-management.md

@@ -1,6 +1,8 @@
 ---
 title: "Disk Management"
 description: "Guide on managing disks"
+aliases:
+  - ../../guides/disk-management
 ---
 
 Talos Linux version 1.8.0 introduces a new backend for managing system and user disks.

website/content/v1.10/talos-guides/configuration/logging.md

@@ -2,7 +2,7 @@
 title: "Logging"
 description: "Dealing with Talos Linux logs."
 aliases:
-  - ../../guiides/logging
+  - ../../guides/logging
 ---
 
 ## Viewing logs

website/content/v1.10/talos-guides/install/single-board-computers/rock5b.md

@@ -0,0 +1,72 @@
+---
+title: "Radxa ROCK 5B"
+description: "Installing Talos on Radxa ROCK 5B SBC using raw disk image."
+aliases:
+  - ../../../single-board-computers/rock5b
+---
+
+## Prerequisites
+
+You will need
+
+- follow [Installation/talosctl]({{< relref "../talosctl">}}) to intall `talosctl`
+- an SD card
+
+## Download the Image
+
+Visit the [Image Factory](https://factory.talos.dev/), select `Single Board Computers`, select the version and select `Radxa ROCK 5B` from the options.
+
+Choose `realtek-firmware` and any other desired extension.
+Next fill in the kernel command line arguments if needed.
+
+Download the image and decompress it:
+
+```bash
+curl -LO https://factory.talos.dev/image/[uuid]/{{< release >}}/metal-arm64.raw.xz
+xz -d metal-arm64.raw.xz
+```
+
+## Writing the Image
+
+This guide assumes the node should boot from SD card.
+Booting from eMMC or NVMe has not been tested yet.
+
+The path to your SD card can be found using `fdisk` on Linux or `diskutil` on macOS.
+In this example, we will assume `/dev/mmcblk0`.
+
+Now `dd` the image to your SD card:
+
+```bash
+sudo dd if=metal-arm64.raw of=/dev/mmcblk0 conv=fsync oflag=direct status=progress bs=4M
+```
+
+## First boot
+
+Insert the SD card into the board, turn it on and proceed by following the
+[getting started guide]({{< relref "../../../introduction/getting-started/#configure-talos-linux" >}})
+for further steps on how to configure Talos.
+
+## Troubleshooting
+
+### Serial console
+
+If you experience any issues you can check the serial console.
+Follow the [official guideline](https://wiki.radxa.com/Rock5/dev/serial-console)
+on how to connect a serial adapter.
+
+Hint: The rock5b overlay uses baudrate of `115200` instead of the default `1500000`
+
+### Power supplies and endless restarts
+
+It is a known issue that USB Power Delivery negotiation is performed at a late stage in kernel.
+This can lead to endless restarts if the power supply cuts power to early.
+Check the list of [known working](https://wiki.radxa.com/Rock5/5b/power_supply) power supplies.
+
+## Tips and tricks
+
+### EPHEMERAL on NVMe
+
+The Radxa ROCK 5B SBC provides a M.2 NVMe SSD slot.
+
+This allows to use a separate disk for the EPHEMERAL partition by following
+[Disk Management]({{< relref "../../configuration/disk-management" >}}).

website/content/v1.9/talos-guides/configuration/disk-management.md

@@ -1,6 +1,8 @@
 ---
 title: "Disk Management"
 description: "Guide on managing disks"
+aliases:
+  - ../../guides/disk-management
 ---
 
 Talos Linux version 1.8.0 introduces a new backend for managing system and user disks.

website/content/v1.9/talos-guides/install/single-board-computers/rock5b.md

@@ -0,0 +1,72 @@
+---
+title: "Radxa ROCK 5B"
+description: "Installing Talos on Radxa ROCK 5B SBC using raw disk image."
+aliases:
+  - ../../../single-board-computers/rock5b
+---
+
+## Prerequisites
+
+You will need
+
+- follow [Installation/talosctl]({{< relref "../talosctl">}}) to intall `talosctl`
+- an SD card
+
+## Download the Image
+
+Visit the [Image Factory](https://factory.talos.dev/), select `Single Board Computers`, select the version and select `Radxa ROCK 5B` from the options.
+
+Choose `realtek-firmware` and any other desired extension.
+Next fill in the kernel command line arguments if needed.
+
+Download the image and decompress it:
+
+```bash
+curl -LO https://factory.talos.dev/image/[uuid]/{{< release >}}/metal-arm64.raw.xz
+xz -d metal-arm64.raw.xz
+```
+
+## Writing the Image
+
+This guide assumes the node should boot from SD card.
+Booting from eMMC or NVMe has not been tested yet.
+
+The path to your SD card can be found using `fdisk` on Linux or `diskutil` on macOS.
+In this example, we will assume `/dev/mmcblk0`.
+
+Now `dd` the image to your SD card:
+
+```bash
+sudo dd if=metal-arm64.raw of=/dev/mmcblk0 conv=fsync oflag=direct status=progress bs=4M
+```
+
+## First boot
+
+Insert the SD card into the board, turn it on and proceed by following the
+[getting started guide]({{< relref "../../../introduction/getting-started/#configure-talos-linux" >}})
+for further steps on how to configure Talos.
+
+## Troubleshooting
+
+### Serial console
+
+If you experience any issues you can check the serial console.
+Follow the [official guideline](https://wiki.radxa.com/Rock5/dev/serial-console)
+on how to connect a serial adapter.
+
+Hint: The rock5b overlay uses baudrate of `115200` instead of the default `1500000`
+
+### Power supplies and endless restarts
+
+It is a known issue that USB Power Delivery negotiation is performed at a late stage in kernel.
+This can lead to endless restarts if the power supply cuts power to early.
+Check the list of [known working](https://wiki.radxa.com/Rock5/5b/power_supply) power supplies.
+
+## Tips and tricks
+
+### EPHEMERAL on NVMe
+
+The Radxa ROCK 5B SBC provides a M.2 NVMe SSD slot.
+
+This allows to use a separate disk for the EPHEMERAL partition by following
+[Disk Management]({{< relref "../../configuration/disk-management" >}}).